Watson-marlow MasoSine Ecosine Assembly Bedienungsanleitung PDF herunterladen

1. Loosen and remove the wing nuts, item 441, and slide the front

cover, item 400, off the studs, item 450. If necessary, a rubber

mallet may be used to separate the cover from the pump

housing by tapping on the front cover pins, item 420.

2. Remove the scrapergate support, item 370, from the front

cover. If the scrapergate support is stainless steel, remove the

dynamic face o-ring, item 515, from the groove.

3. The front cover o-ring, item 430, may now be removed from

the groove in the pump housing face.

Assembly/Disassembly Instruction Sheet

NOTE

Reference the isometric drawing for parts

identification while following the wet end

disassembly and assembly steps.

7. Remove the rear liner, item 072. This is where the liner/seal

housing removal tools will be helpful. Insert the hooked ends of

the liner pullers into the slots located on each end of the liner.

Again, apply even pressure on both ends to prevent the liner

from lodging in the pump housing.

6. Next, the rotor, item 011, the scrapergate, item 125, and the

scrapergate guide, item 100, can be pulled off the shaft and

removed from the pump housing. This will require two hands.

4. Remove the front liner, item 072, by pulling with even pressure

on both ends.

5. Remove the shaft nut, item 231. Wrench flats have been

machined into the rear of the shaft to secure the shaft while

loosening the nut. The rotor o-ring, item 030, can now be

removed from the groove in the shaft nut.

WARNING:

Before attempting assembly/disassembly of the Sine Pump, be sure that the power source to the drive is disconnected or

locked out. Ensure that the electrical switch gear cannot be operated while work is performed on the pump. Failure to do so

could result in severe personal injury from rotating components.

TOOLS

Removal tools are supplied with every new Sine Pump. The

tools are shaped like skate blades and have a pin extending

from one end. These tools are used for removing the rear liner

and seal housing.

Steps: 1, 2, 3

Steps: 4, 5

Step: 7

Steps: 8, 9, 10

Step: 6

WET END DISASSEMBLY

8. The seal housing, item 500, along with the shaft sleeve, item

530, may now be removed from the pump housing, using the

pinned end of the removal tools. Insert the pins on the pullers

into the holes in the outer diameter of the seal housing,

located 180 degrees from each other and lever the seal

housing out of the pump housing. If the seal housing is

stainless steel, remove the dynamic face o-ring, item 515,

from the groove.

9. Remove the shaft sleeve, item 530, from the seal housing.

The rotor o-ring, item 030, may then be removed from the

groove in the flanged end of the shaft sleeve.

10. Next, remove the seal housing o-ring, item 540, from the

groove in the rear of the pump housing. A small notch has

been machined into the rear bore of the pump to facilitate this.

420

430

231

030

500

300

072

441

400

370

420

072

450

540

030

011

515

530

515

125

100

450

441

400

420

515

370

430

Liner Removal End

SIDE

FRONT VIEW

Seal Housing

Removal End

540

500

030

530

515

300

072

231

072

125

011

100

WET END DISASSEMBLY

1 2

Inhaltsverzeichnis

Seite 1 - WET END DISASSEMBLY

1. Loosen and remove the wing nuts, item 441, and slide the frontcover, item 400, off the studs, item 450. If necessary, a rubbermallet may be used to

Seite 2 - WET END ASSEMBLY

6. Place the scrapergate, item 125, into the scrapergate guide,item 100, being sure that the marked ends (SL and SR) matchup properly. See Appendix 2

Verwandte Modelle: SPS Assembly | MR Assembly |

Kommentare zu diesen Handbüchern

Keine Kommentare

Watson-marlow MasoSine Ecosine Assembly Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Watson-marlow MasoSine Ecosine Assembly herunter. Watson-Marlow MasoSine Ecosine Assembly User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: SPS Assembly | MR Assembly |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Watson-marlow MasoSine Ecosine Assembly